Anticorrosive wood floor stainless steel metal fastener floor buckle fastener hardware fittings small seam large buckle
Special floor fastener for anticorrosive wood pavement
sealing pavement hardware fastener
Application: outdoor landscape anti-corrosion wood floor, plastic wood, heavy bamboo floor, ecological wood floor hardware fastener
length 5cm * width 3cm * height 2.5cm (fastener appearance size, only cap hat manufacturer for reference)
this fastener is concealed, so that the panel has no nails, does not damage the wood and is beautiful.
This fastener is a large fastener, which is suitable for thick floor. The seam after installation is small, which is generally 2-3mm. The size is only for reference
this fastener has strict requirements on the height of floor groove and lower groove, which is suitable for the height of 17.9mm. Suitable for thick floor, at least 40mm thick floor. If the total thickness of the floor is below 328mm, it is not recommended to consider this section.
manual measurement, the size error is about 1 mm, please understand.
The fastener size is 17.9mm in inner height and 8.8mm in foot length. The slot height suitable for slot plate is more than 2mm, the groove depth is greater than 8.8mm, and the cap-hat-manufacturer lower groove height is accurate 17.9mm;
if the floor is 40 thickness, the slot size is: lower groove 18, slot height 2, upper groove 20mm
if the floor is 50 thickness, the slot size is: lower slot 18, slot height 2, upper slot 30mm
the slotting size is only for reference, It can be opened according to your own needs. The key is that the height of the lower groove corresponds to the height of the fastener.
(Note: because this section is close seam pavement, it is suitable to protect hardwood such as plastic wood and pineapple, and the board is not easy to deform, so it is not suitable for use on cork. Although it is a close seam shop, there will be about 2-3mm smallIf the measurement of your board is not within the range of our listed data, you can report the three key data of your board to the customer service, and the customer service will provide you with fasteners suitable for your board according to your size. 》
important notes:
1. The size of each fastener is different, and not all fasteners can be equipped with all trough plates. Therefore:
when fitting fasteners, you must measure the data in the figure above, otherwise the fasteners may not be suitable for your board.
2. Buy the fastener first and then arrange the board slotting:
if you take the fastener back and slot again, it is the safest and worth recommending
3. Ask for the fastener sample free of charge, and contact customer service:
if you don't trust the quality, or if you are afraid of wrong size, whether you can use it, if you need samples, all the fasteners sold in our store can send samples free of charge, We don't bear the freight, so in a hurry, you can send it to SF express, you can also send it to ordinary express, or you can take one cap-hat-manufacturer online and contact customer service to modify the price!
The installation effect of the following pictures is only for reference, general installation.
for screws, please click the following link:
note to the buyer: once the fastener series is sold, if it is not a quality problem, no return service will be provided. If you need to exchange goods, you can negotiate with the customer service. Please see the size before shooting, we can send samples for trial use, and the freight will be borne by the buyer.
Special floor fastener for anticorrosive wood pavement
sealing pavement hardware fastener
Application: outdoor landscape anti-corrosion wood floor, plastic wood, heavy bamboo floor, ecological wood floor hardware fastener
length 5cm * width 3cm * height 2.5cm (fastener appearance size, only cap hat manufacturer for reference)
this fastener is concealed, so that the panel has no nails, does not damage the wood and is beautiful.
This fastener is a large fastener, which is suitable for thick floor. The seam after installation is small, which is generally 2-3mm. The size is only for reference
this fastener has strict requirements on the height of floor groove and lower groove, which is suitable for the height of 17.9mm. Suitable for thick floor, at least 40mm thick floor. If the total thickness of the floor is below 328mm, it is not recommended to consider this section.
manual measurement, the size error is about 1 mm, please understand.
The fastener size is 17.9mm in inner height and 8.8mm in foot length. The slot height suitable for slot plate is more than 2mm, the groove depth is greater than 8.8mm, and the cap-hat-manufacturer lower groove height is accurate 17.9mm;
if the floor is 40 thickness, the slot size is: lower groove 18, slot height 2, upper groove 20mm
if the floor is 50 thickness, the slot size is: lower slot 18, slot height 2, upper slot 30mm
the slotting size is only for reference, It can be opened according to your own needs. The key is that the height of the lower groove corresponds to the height of the fastener.
(Note: because this section is close seam pavement, it is suitable to protect hardwood such as plastic wood and pineapple, and the board is not easy to deform, so it is not suitable for use on cork. Although it is a close seam shop, there will be about 2-3mm smallIf the measurement of your board is not within the range of our listed data, you can report the three key data of your board to the customer service, and the customer service will provide you with fasteners suitable for your board according to your size. 》
important notes:
1. The size of each fastener is different, and not all fasteners can be equipped with all trough plates. Therefore:
when fitting fasteners, you must measure the data in the figure above, otherwise the fasteners may not be suitable for your board.
2. Buy the fastener first and then arrange the board slotting:
if you take the fastener back and slot again, it is the safest and worth recommending
3. Ask for the fastener sample free of charge, and contact customer service:
if you don't trust the quality, or if you are afraid of wrong size, whether you can use it, if you need samples, all the fasteners sold in our store can send samples free of charge, We don't bear the freight, so in a hurry, you can send it to SF express, you can also send it to ordinary express, or you can take one cap-hat-manufacturer online and contact customer service to modify the price!
The installation effect of the following pictures is only for reference, general installation.
for screws, please click the following link:
note to the buyer: once the fastener series is sold, if it is not a quality problem, no return service will be provided. If you need to exchange goods, you can negotiate with the customer service. Please see the size before shooting, we can send samples for trial use, and the freight will be borne by the buyer.
Комментарии
Отправить комментарий